Messages

1

Projects - Glacier Boats of Alaska boat projects / Re: Bob from Olympia, 28 GA build

« on: June 30, 2025, 07:20:48 AM »

Can you post the total cost of you install?

2

Projects - Glacier Boats of Alaska boat projects / Re: Bob from Olympia, 28 GA build

« on: May 13, 2025, 08:52:09 PM »

You say it worked well? Have you ever used a bow thruster before? How does it compare to your past experience?

3

Projects - Glacier Boats of Alaska boat projects / Re: Bob from Olympia, 28 GA build

« on: May 07, 2025, 02:24:01 PM »

Do you have a link on those thrusters, such a cool design. Can?t wait to see how the work

4

Boat Systems - Electrical, Electronics, Motors, Plumbing & Tankage etc / Re: fuel tanks

« on: February 13, 2025, 07:21:34 AM »

Make sure they vent both ends of the tank if you have one built.

5

General Discussion about the Great Alaskan / Re: Knife valves for scuppers?

« on: February 11, 2025, 06:27:23 PM »

I love the idea. Can?t wait to see it implemented

6

Boat Systems - Electrical, Electronics, Motors, Plumbing & Tankage etc / Solar vs charger

« on: February 11, 2025, 05:58:20 PM »

I am thinking about adding solar. I currently have a battery charger on board for when I?m in port or at home which keeps my starter and house batteries topped off. When I add solar, is there any concern with having the solar charging the battery?s at the same time at the charger. In other words should I only use one at a time.

7

Introductions - Are you new here? Say hello! / Re: Cruising focused GA 30

« on: December 30, 2024, 09:08:36 PM »

Sounds like you?re on the same path I took. Was convinced for years I was building a Delvin black crown until I came across Brian?s boat. I rented a black crown several times from Sam and loved it. It was a very heavy boat. The great Alaskan is much more lighter and responsive in comparison. For me I made the rights choice. Devlins are very cool also

8

General Discussion about the Great Alaskan / Dry decking

« on: November 23, 2024, 08:41:58 PM »

I recently found this decking on Amazon and really like it. It?s a lot cheaper the dry deck and is an outstanding product

Big Floors DT40GRAY DuraGrid Outdoor Modular Interlocking Multi-Use Plastic Deck Tile, 40 Pack, Gray

9

Projects - Glacier Boats of Alaska boat projects / Re: 13 Bananas New Jersey Kodiak

« on: November 20, 2024, 08:16:29 AM »

I agree with Brian and Dan. All the faring and sanding is over the top and going to make a beautiful boat. Love the boat

10

General Discussion about the Great Alaskan / Re: extended swim platform

« on: November 08, 2024, 05:48:21 PM »

Only thing I would have done different is to slope the back deck to the rear 1 to maybe 1 1/2 inches. I enjoy this boat so much. Have thought about building a new one but don?t want to get off the water to do it. Just been upgrading a few things so I can spend more time on it.

11

General Discussion about the Great Alaskan / Re: extended swim platform

« on: November 08, 2024, 12:50:59 PM »

I love your idea. I also extended and put in a tuna door. Makes getting on the boat easy, from the dock or out of water

12

Boat or Boat Building (or related) Items For Sale / Oil changer

« on: July 05, 2024, 06:54:59 AM »

Have an oil changer I no longer need . $120. Ill send it to you used one time on my Alaska trip.

13

General Discussion about the Great Alaskan / Paint touch up

« on: June 05, 2024, 08:03:22 AM »

Looking for a little advise. Thinking about putting some fresh paint on the rear deck area. I painted with alexseal . My question is while I?m repainting I was thinking of faring a few areas that I didn?t get smooth the first time around. How far do I  need to sand down to fix these spots ? Can I just use an automotive filler and then paint. Thoughts?

14

Blood on the Deck! (And Other Grand Adventures!) / Re: Spring protein run

« on: May 18, 2024, 11:23:54 AM »

Very nice

15

General Discussion about the Great Alaskan / Re: Issue with fuel tank/s

« on: April 13, 2024, 09:08:10 AM »

Fortunately my tank builder was smarter then I am, he put a vent on both ends. Never had an issue.